Round steel cutting machine manufacturers share the safety operation rules of steel cutting machine:

一、切斷機四周應有足夠的鋼筋堆放場地。

1. There should be enough reinforcing steel yard around the cutter.

二、轉動的部件應有防護罩。

2. The rotating parts should have protective cover.

三、須檢查刀片有無裂紋，刀片固定螺絲是否緊固。

3. It is necessary to check whether the blade is cracked and whether the fixing screw of the blade is tightened.

四、不準用兩手分別握住鋼筋的兩端剪切，只準用手握住靠身邊一端的鋼筋上。

4. Do not hold the two ends of the reinforcing bar with two hands separately, only hold the reinforcing bar on the side with one hand.

五、工作時用雙手握住鋼筋，對準刀口，待上刀片下來覺得壓手時，立即用力壓住鋼筋，防止尾端翹起傷人。

Fifth, when working, hold the steel bar with both hands and aim at the edge of the knife. When the knife blade comes down and feels pressure on the hand, press the steel bar vigorously immediately to prevent the tail end from warping up and hurting people.

六、 禁止切斷直徑超過機械規定的鋼筋和燒紅的鋼筋，多根鋼筋同時切斷時，必須換算鋼筋的截面，及時調整刀片，以防止意外。

6. It is forbidden to cut reinforcing bars with diameters exceeding the mechanical requirements and red-burning reinforcing bars. When multiple reinforcing bars are cut at the same time, the section of reinforcing bars must be converted and the blades adjusted in time to prevent accidents.

七、切斷低合金鋼筋時，應換高硬度刀片。

7. When cutting low alloy steel bar, high hardness blade should be replaced.

八、切斷短料時，手握一端的長度不得小于４０ｃｍ，靠近刀片手與刀片的距離，應保持在１５ｃｍ以上。

8. When cutting short material, the length of one end of the hand should not be less than 40 cm, and the distance between the hand and the blade should be kept above 15 cm.

九、切斷較長鋼筋時，應有專人幫扶鋼筋，幫扶人與操作人動作一致，并聽其指揮不得任意拖拉。

9. When cutting long reinforcing bars, special people should help reinforcing bars, help people and operators to act in accordance, and listen to their command can not be arbitrary procrastination.

十、機械運轉中嚴禁用手清理刀口附近的雜物，現場禁止閑雜人員逗留。

10. It is strictly forbidden to clean up the debris near the edge of the knife by hand during the operation of the machine. It is forbidden for idle and miscellaneous personnel to stay at the scene.

十一、發現刀片歪斜異常現象，應立即斷電檢修。

11. Discovering abnormal deflection of blade, the power should be cut off and repaired immediately.http://lala-tm.com